1. Detect the leakage of pipe systems on cars, motorcycles.
2. 4ft Smoke Outlet Pipe can help reach and connect perfectly.
3. Smoke Output Value: 10-20L/min. Output Pressure: 10-20PSI.
AUTOOL SDT-206 Automotive EVAP Leak
Testing Machine, 12V Vehicle Pipes Fuel Leakage Detector Diagnostic Tester for
Cars/Motorcycles/Boats
Featured
l WORKING PRINCIPLE -- The
Smoke Machine heat up special oil(mineral oil or baby oil) into smoke and blow smoke
into sealed pipe system. You will find out leak point in pipe in where has
smoke. Please repair the part where leakage exists.
l CONVENIENT MACHANICS TOOL
-- The SDT-206 is a simple-using Smoke Machine for techs to detect the leakage
of pipe systems on cars, motorcycles, such as fuel pipe, air intake system and
cooling tank.
l EVAP SYSTEM SUPPORTED --
Comes with EVAP adapters, SDT-206 can help you apply with EVAP System of all
vehicles to quickly find out the leak parts. 4ft Smoke Outlet Pipe can help reach
and connect perfectly.
l SPECIFICATIONS -- Voltage:
DC 12V(Supplied by Automotive Battery). Smoke Output Value: 10-20L/min. Output
Pressure: 10-20PSI. Heating Material: Mineral Oil or Baby
Oil(oil not included). Addjustable Flow Switch help control easily.
l 3 YEARS WARRANTY -- 3-7
days fast shipment via DHL. To ensure your high-quality shopping experience, we
provide 3 years warranty(longer than competing machines). 24 hours E-mail
supports can help resolve any issues of using. Buy and use with confidence.
Product description
Kindly Note:
1 Avoiding test smoke-sensitive parts with this
machine.
2 The machine can work on EVAP system with
specific adapter (pressure of machine was larger than EVAP request ).
3 Don't work with the machine continuously more
than 8 minutes.Bottom of the machine will give out heat,be careful!
4 Injection paraffin oil or baby oil in machine
before detecting (oil is not included in the pack)
How to
change oil?
1. Inject 20-30ml oil in the machine when use it
in the first time.
2. When smoke become weak or go out with steam,
it means we should change oil, release residue then injection new oil in
machine ( LESS than 15ml )
Ways of
Use:
1.Open the engine cover, and hang the detector
in the cover.
2.Disconnect the pipe that needs to be connected
with detector. If the pipe needs to be disconnected in the middle, please
secure the other side with a rubber stopple.
3.Secure this side with proper taper
stopple/pipe, and connect it with smoke output tube.
4.Connect detector with DC12V battery: red with
positive, black with negative. Do not connect in a contrary way.
5.Turn on the power switch, and detector starts
to work.
6.In about 3 minutes, the pipe will be filled
with smoke. Check the leak points. Please use head lamp if necessary.
7.After leak detection, please connect well the
wires and pipe.
8. Please repair the leak part timely with
specific tool.
Dimension of host |
270×150×150mm(10.6" ×6" ×6") |
Package weight |
5kg(11lb) |
Package size |
300×235×320mm(11.8" ×9" ×12.6") |
Output pressure |
10-18 psi |
Output flow |
10-20L/min(2.2-4.4GPM) |
Air supply mode |
Built-in air pump |
Power supply |
12V vehicle battery |
Fluid capacity |
40ml(0.0088Gal) |
1x Main Unit
1x.Hook (with hand-tighten nuts)
1x End cap kits
1x Taper plug
1x Taper pipe
1x Air Sac
1x Oil bottle
1x User manual